Router Table Inserts
For the installation of the router in a self-built routing table, there is no way around a suitable insert plate. In recent years, aluminium insert plates have become the preferred choice, as they are more scratch-resistant, stable and dimensionally stable compared to plastic.
We offer a variety of insert plates, which are already pre-drilled to fit the most common routers.
Read more
for stationary routing with guide bushes | use with US copy sleeves | for all sauter insert plates and lifts with steel reduction plates
Item no.: SA-RP-GBDelivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel to close the opening
Item no.: SA-RP2.0-0Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø 10 mm
Item no.: SA-RP2.0-10Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø 16 mm
Item no.: SA-RP2.0-16Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 22 mm
Item no.: SA-RP2.0-22Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 32 mm
Item no.: SA-RP2.0-32Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 42 mm
Item no.: SA-RP2.0-42Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 54 mm
Item no.: SA-RP2.0-54Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 68 mm
Item no.: SA-RP2.0-68Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 86 mm
Item no.: SA-RP2.0-86Delivery in 1-2 business days
for sauter premium insert plate ELP2.0, OFL2.0 & OFL3.0 | made of galvanised, 2 mm thick steel with cutter opening Ø- 98 mm
Item no.: SA-RP2.0-98Delivery in 1-2 business days
for levelling the reduction plates for ELP & OFL | Disc thickness: 0.1 mm | Ø 20 mm |- magnetic stainless steel
Item no.: SA-99600010Delivery in 1-2 business days
for the installation of mounting plates and OFLs | 20-piece set made of high-quality aluminium
Item no.: SA-99600005Delivery in 1-2 business days
Starter pin for insert plates | suitable for all sauter ELP, OFL & FO-RTS plates with 1/4" thread
Item no.: FO-RTS-I2-03Delivery in 1-2 business days
Spare plastic rings for insert plates and router lifts | suitable for: sauter ELP1.0 & OFL1.0, insert plates RTS1 & RTS2
Item no.: FO-CRT24Delivery in 1-2 business days
Corner fixing set for insert panels | with 4 clips, screws and nuts each
Item no.: T-WP-RTI-04Delivery in 1-2 business days
For stationary routing with guide bushes | 7 guide bushes | for all sauter insert plates and lifts with steel reduction plates
Item no.: SET-SA-RP-GB-MDelivery in 1-2 business days
Correct attachment of the router
When constructing a routing table yourself, it is essential to keep the attachment for the router clean. First the mounting plate must be prepared. The router is used for this purpose under the plate. If there are no holes in the plate, these must still be drilled. Then you can start building the board into the routing table. Two to three Screws are usually sufficient for correct attachment of the router.
This allows the router to be quickly and easily removed from the self-built routing table so that it can be used as a mobile hand router again. If you build your own routing table, you can it is important to carefully reline the router mounting plate in the rebate of the table surface until the plate surface is exactly flat with the surface of the router table.