Which materials can be rmachined with a SmartBench?

Machining of wood materials, e.g. softwood, hardwood and sheet materials, aluminium, as well as plastics is possible with the CNC router.

Which routing method is used to achieve clean cut edges?

This depends on the CNC router cutter used. For a clean top edge, we recommend CNC spiral flute cutters VHM with left-hand twist. The pressure on the material produces absolutely tear-free cutting edges. For the bottom side, a router with right-hand twist is used. If both cutting edges are to be machined in one process, so-called compression routers or dual-cut routers can be used, which have an opposite twist in different areas of the cutting edges. The left-hand twist at the end of the shaft ensures a tear-free top side, while the right-hand twist at the tip of the router ensures a tear-free bottom side.

When should edges be reworked?

For example, with whirling, the offset cut often results in unclean edges, which then have to be machined either manually or by a further CNC work step. Rough milling cutters also do not leave a high surface quality. Here, too, reworking is necessary, either manually or with a final finishing pass. In most CAM programs, it is possible to perform a final finishing pass, which is usually performed over the entire thickness of the material. Here the material is delivered to the area of the uniform cut edge.

What should be considered when routing the different materials?

One of the main factors for a successful routing result is the interaction of feed and speed. If the tool rotates too fast compared to the feed rate, no real chip is removed and the tool rubs more against the workpiece and generates dust. With wood, this leads to burns on the material and the router bit also wears out very quickly. With plastics and aluminium, this can quickly cause major problems.Plastic: gets too hot and melts instead of being cut.Aluminium: it can cause the aluminium to weld itself to the router bit, destroying both the workpiece and the router bit.If, on the contrary, the speed is too low, this means too high cutting forces for the router bit, which often leads either to breakage of the router bit or to step losses at the stepper motors. This then leads to incorrectly converted routing paths and a destroyed workpiece.

What should be considered when choosing tools?

In principle, there are also special tools designed for different materials and cutting types. These differ both in the material (HSS, carbide, etc.) and in the cutting geometries.Roughing cutters, for example, have a rather aggressive cutting angle in order to remove a lot of material quickly without attaching great importance to the quality of the cut.Finishing cutters remove little material and leave a clean cutting edge. Accordingly, flatter cutting angles are used here.Routers with carbide cutting edges are suitable for wood and aluminium. These are either soldered to a steel shank (classic end mills for routers) or consist entirely of a carbide mixture. The number of cutting edges also plays a role in the tool life and the milling result. For aluminium, for example, single-edged cutters are often used to give the machine more time and to be able to remove the cut chips cleanly.

What settings should be considered when routing?

The most important key figures in routing are: Feed rate, speed and infeedWhen routing pockets with many parallel toolpaths, a transverse infeed of <50% is often used. This means that each milling path overlaps only half of the previous path. The additional milling time required can then be compensated by a higher feed rate. The decision "climb milling or up-cut milling" can also have a decisive influence on the milling result. The correct cutting speed cannot be answered in a blanket manner. The best results are achieved when the CNC router is used to carry out some test routing in scrap stock.

How can intricate details also be achieved during routing?

If possible, it should be plunged outside the contours to be routed in order to then approach the contour to be routed from the side. In addition, a final finishing pass often leads to a cleaner, better result, as only a little material is removed and the router is also only loaded with 10-20% cross feed. When routing very delicate details (e.g. 0.5 mm cutter), patience is a virtue. Even if router and machine would manage higher feeds and speeds without any problems, with wood materials more defensive cutting values often lead to less tear-out on intricate routed parts.

When to choose a down cutting or up-cut milling?

When machining manually, e.g. at the router table with a router, only up-cut routing is permitted. When routing in the same direction, the material is drawn towards the cutter, which entails some safety risks and dangers. When machining on the CNC, the situation is different. The overall rigidity and the backlash of the machine determine whether down cutting is possible or useful.If the machine allows it, however, down cuttingis preferred in the CNC area, as it has a number of advantages:Longer routing cutter service lifeLower cutting forcesChip ejection behind the router and thus less "multiple machining" of chipsBetter surface quality

Fresatrice CNC

Una fresatrice CNC (CNC = controllo numerico computerizzato) è una macchina programmata con un computer per fresare pezzi da vari materiali. La fresatrice CNC ha diversi assi che possono muoversi indipendentemente l'uno dall'altro.

La gamma di fresatrici CNC compatte e flessibili è in continua crescita e offre alle piccole imprese e agli appassionati di lavorazione del legno con laboratori più piccoli una serie di opzioni: Una soluzione completa a controllo numerico, come SmartBench di Trend , o una fresa verticale portatile, come Origin di Shaper Tools.

Leggi di più

griffmuldenfraeser-hw-hm-22x16-shaper-tools-st-sf1-8-fpc-01

Fresa per sagomatura HW (HM) 22 x 16 mm

Ideale per creare incastri a coda di rondine

n. art.: ST-SF1-8-FPC

In magazzino, consegna in 1-2 giorni lavorativi

97,60 €

spiralnutfraeser-zweischneidig-shaper-tools-st-sf1-8-4f2-01

Fresa a spirale per scanalature 4 mm x 15 mm, a doppio taglio

D: 4 mm | GL: 80 mm | NL: 15 mm | Z: 2 | S: 8 mm

n. art.: ST-SF1-8-4F2

In magazzino, consegna in 1-2 giorni lavorativi

85,40 €

gravierfraeser-vhm-60-shaper-tools-st-sf1-8-v60e-01

Fresa per incisione in carburo solido 60°

E: 90° | GL: 38 mm mm | NL: 3,175 mm | Z: 2 | S: 6,35 mm

n. art.: ST-SF1-8-V60E

In magazzino, consegna in 1-2 giorni lavorativi

32,94 €

gravierfraeser-vhm-90-shaper-tools-st-se1-2500-v90e-01

Fresa per incisione in carburo solido 90°

E: 90° | GL: 38 mm mm | NL: 3,175 mm | Z: 2 | S: 6,35 mm

n. art.: ST-SE1-2500-V90E

In magazzino, consegna in 1-2 giorni lavorativi

30,50 €

t-nut-fraeser-hw-hm-d105-shaper-tools-st-sf1-8-tsc-01

Fresa per scanalature a T HW (HM) D10,5 mm

D: 10,5 mm | GL: 50 mm | NL: 12 mm | GSL: 5 mm | Z: 2 | S: 8 m

n. art.: ST-SF1-8-TSC

In magazzino, consegna in 1-2 giorni lavorativi

46,36 €

zinkenfraeser-15-shaper-tools-st-sf1-8-dc15-01

Fresa a dentiera 15 ̊

Ideale per creare incastri a coda di rondine

n. art.: ST-SF1-8-DC15

In magazzino, consegna in 1-2 giorni lavorativi

46,36 €

keilverbinder-funktionsmuster-shaper-keilverbinder-kv-m-shaper-01

Connettore a cuneo Campione funzionale Shaper

Per costruzioni speciali, aree hi-fi, design, ecc. | Modello: Shaper | Materiale: MDF 12 e 19 mm

n. art.: KV-M-SHAPER

In magazzino, consegna in 1-2 giorni lavorativi

5,13 €

spannzange-mutter-shaper-tools-st-sd1-6-01

Pinza di serraggio con dado Ø 6 mm

Compatibile con Shaper Origin (Gen1, Gen2)

n. art.: ST-SD1-6

In magazzino, consegna in 1-2 giorni lavorativi

52,46 €

spannzange-mutter-shaper-tools-st-sd1-3-01

Pinza di serraggio con dado Ø 3 mm

Compatibile con Shaper Origin (Gen1, Gen2)

n. art.: ST-SD1-3

In magazzino, consegna in 1-2 giorni lavorativi

52,46 €

spannzange-mutter-shaper-tools-st-sd1-8-01

Pinza di serraggio con dado Ø 8 mm

Compatibile con Shaper Origin (Gen1, Gen2)

n. art.: ST-SD1-8

In magazzino, consegna in 1-2 giorni lavorativi

52,46 €

keilverbinder-profilschiene-keilverbinder-kv-s-1490-0-01

Profilo di raccordo a cuneo 1490

Tenuta stabile del connettore a cuneo | Installazione semplice | Dimensioni standard | Personalizzabile

n. art.: KV-S-1490-0

In magazzino, consegna in 2-3 giorni lavorativi

Merce ingombrante

15,85 €

spannzange-mutter-shaper-tools-st-sc1-1250-01

Pinza di serraggio con dado Ø 3,175 mm (1/8")

⅛" | 3,175 mm | per Shaper Origin

n. art.: ST-SC1-1250

In magazzino, consegna in 1-2 giorni lavorativi

52,46 €

spannzange-mutter-shaper-tools-st-sc1-2500-01

Pinza di serraggio per sagomatori con dado Ø 6,35 mm (1/4")

Compatibile con il mandrino Shaper SM1

n. art.: ST-SC1-2500

In magazzino, consegna in 1-2 giorni lavorativi

52,46 €

Nuovo

Trend SmartBench Precision Pro PLUS v1.4

il primo controllo autonomo della velocità al mondo | v1.4 | lavorazione fino a 2500 x 1250 mm

n. art.: YT-CNC-YPPP-SB2

Tempi di consegna 18 giorni lavorativi

Spedizione con spedizioniere

15.250,00 €

spiralnutfraeser-3175mm-einschneidig-shaper-tools-st-se1-2500-5000c-01

⅛" X ½" Fresa per scanalature a spirale Monoaletta

S: 0,25” (6,35 mm) | D: 0,125” (3,175 mm)

n. art.: ST-SE1-2500-5000C

In magazzino, consegna in 1-2 giorni lavorativi

46,36 €

spiralnutfraeser-635mm-shaper-tools-st-se1-2500-1000c-01

Fresa a spirale da ¼" X 1"

S: 0,25" (6,35 mm) | D: 0,25" (6,35 mm)

n. art.: ST-SE1-2500-1000C

In magazzino, consegna in 1-2 giorni lavorativi

32,94 €

spiralnutfraeser-635mm-einschneidig-shaper-tools-st-se1-2500-1500c-01

Fresa per scanalature a spirale da ¼" X 1½", a una sola elica

Gambo: 0,25" (6,35 mm) | Diametro: 0,25" (6,35 mm)

n. art.: ST-SE1-2500-1500C

In magazzino, consegna in 1-2 giorni lavorativi

59,78 €

spiralnutfraeser-3175mm-einschneidig-shaper-tools-st-se1-2500-2500c-01

⅛" X ¼" Fresa per scanalature a spirale Monoaletta

S: 0,25” (6,35 mm) | D: 0,125” (3,175 mm)

n. art.: ST-SE1-2500-2500C

In magazzino, consegna in 1-2 giorni lavorativi

39,04 €

hohlkehlfraeser-635mm-shaper-tools-st-se1-2500-bnus-01

Fresa a tazza da ¼" X ¾"

D: 0,25" (6,35 mm) | NL: 19,05 mm | GL: 63,5 mm | S: 0,25" (6,35 mm) | Z: 2 | Torsione a destra

n. art.: ST-SE1-2500-BNUS

In magazzino, consegna in 1-2 giorni lavorativi

36,60 €

cnc-fraese-precision-pro-plus-yetitool-yt-21327-01

SmartBench PRECISION PRO PLUS (V1.3)

il primo controllo autonomo della velocità al mondo | v1.3 | PRECISION PRO PLUS | Lavorazione fino a 2500 x 1250 mm

n. art.: YT-21327

I rifornimenti sono in arrivo

Spedizione con spedizioniere

15.250,00 €

Dettagli

shaper-origin-screen-protector-shaper-tools-st-su1-csp1-01

Protezione dello schermo Shaper Origin (Gen 1)

Protegge lo schermo di Origins (Gen 1) da graffi, sporco e polvere.

n. art.: ST-SU1-CSP1

In magazzino, consegna in 1-2 giorni lavorativi

42,70 €

Spazzole in carbonio con smorzamento e spegnimento in silicone

per tutti i motori fresa AMB (1 coppia) Carbonio di qualità prodotto in Germania

n. art.: SET-AMB-35635

In magazzino, consegna in 1-2 giorni lavorativi

22,18 €

x-y-axis-stepper-smartbench-trend-yt-wp-cncy-051-01

Motore passo-passo sostitutivo per l'asse X/Y per SmartBench

Compatibile con tutti i modelli SmartBench dalla versione 1.2 PRO in poi

n. art.: YT-WP-CNCY-051

Disponibile dal 24.08.2026

217,65 €

tastplatte-smartbench-trend-yt-wp-cncy-011-01

Piastra tattile Yetitool completa

compatibile con tutti i modelli SmartBench | per la regolazione dello zero Z

n. art.: YT-WP-CNCY-011

In magazzino, consegna in 1-2 giorni lavorativi

45,01 €

Provate dal vivo le fresatrici CNC SmartBench e Shaper Origin

Video e immagini non vi bastano? Allora avete la possibilità di prenotare una dimostrazione esclusiva della SmartBench o della Shaper Origin. I nostri esperti vi consiglieranno in loco nella nostra splendida sede di Ammersee o dal vivo tramite una demo online e vi mostreranno tutte le funzioni e i vantaggi delle fresatrici CNC.Prenotate qui il vostro appuntamento personale.

Lingua

Fresatrice CNC

Filtra e ordina

Provate dal vivo le fresatrici CNC SmartBench e Shaper Origin